Application — Formaldehyde

Measuring What the Industry Standard Demands

Formaldehyde emission testing for wood-based panels, furniture, and building materials — from raw production to finished products. Compliant with EN ISO 717-1, ASTM D6007, ASTM E1333.

MethodFluorimetric · EN ISO 717-1 / ASTM D6007 / ASTM E1333
Detection Range0.1 ppb – 3000 ppb (gas) · 150 ng/l – 5 mg/l (liquid)
Sample PhaseGas and liquid phase
InstrumentAL4021
→ View AL4021 Specs

Why Formaldehyde Testing Is Getting Harder

The new EU formaldehyde limits (Regulation (EU) 2023/1464, applicable from 6 August 2026) are tightening emission thresholds in furniture, flooring, and building materials. Manufacturers, test laboratories, and independent auditors face stricter requirements — and need instruments that are already norm-referenced and deliver reliable results in the low ppb ranges.

Classic DNPH cartridge + HPLC methods are time-consuming, expensive per sample, and require external lab capacity. Photometric alternatives exist, but lack the sensitivity needed for low-emission materials under the new limits.

Relevant norm: Commission Regulation (EU) 2023/1464 of 14 July 2023 amending Annex XVII to Regulation (EC) No 1907/2006 of the European Parliament and of the Council as regards formaldehyde and formaldehyde releasers


How AL4021 Solves This

Single Instrument — Up to max. 16 Test Chambers
One AL4021 can switch between multiple test chambers sequentially. No need to duplicate instruments per chamber — dramatically lowers per-sample cost.
PPB-Level Detection — Well Below E1 Limits
Fluorimetric detection (not IR) reaches the low ppb range continuously and online, without sample collection and lab turnaround, which DNPH/HPLC cannot offer. Essential for testing low-emission materials.
Direct Compliance Measurement
Method listed in EN ISO 717-1, ASTM D6007 (gas-phase, small chamber), and ASTM E1333 (gas-phase, large chamber). No conversion factors, no secondary validation needed.
Gas + Liquid in One Device
The AL4021 can switch between gas-phase emission measurement (test chamber) and liquid-phase analysis (e.g., process water).
Interested in this application?

Discuss your measurement requirement with our specialists.

Our application engineers advise on instrument configuration, regulatory compliance, and system integration for your specific task.

Request Quote → Technical Inquiry → Datasheet AL4021 (PDF)
Used By
Furniture Manufacturers Wood Panel Producers Test Laboratories Building Material Auditors Environmental Agencies
References
  • IKEA
  • BASF
  • Daiken Southland (New Zealand)
  • IUTA Duisburg (Germany)

Comparison of Measurement Methods

How does fluorimetric detection compare to common alternatives? The table below shows the critical parameters for formaldehyde measurement in emission testing.

Parameter AL4021 Fluorimetric IR AbsorptionDNPH Cartridge + HPLCElectrochemical Sensor
Detection Limit <100 ppt (gas) · <150 ng/l (liquid) <1 ppb (gas), only for pure HCHO in carrier gas 0.04 ppb 10 ppb
Response Time ~90 s (T90), delay ~300 s Few minutes 24 – 48 hours (lab turnaround) 60 s
Multi-Chamber Capable Yes (multiple chambers sequential) Yes No (one sample at a time) No
Gas + Liquid Yes — both in one instrument Gas only Both (separate preparation) Gas only
Norm Reference EN ISO 717-1 / ASTM D6007 / E1333 Not listed ISO 16000 / VDA 276 Not listed
Cross-Interferences Documented · very selective CO₂, CH₄ overlap possible Very low Humidity dependent
Calibratable On-Site Yes — traceable Not always possible External lab required Drift, limited traceability
Per-Sample Cost Low (automated; reagent consumption only) Low High (per-cartridge + lab) Medium (sensor replacement)

AL4021 — Key Specs

Instrument specifications relevant to this application. Full data sheet available for download.

Detection Limit
<100 ppt (gas) · <150 ng/l (liquid)
Range
0.1 ppb – 3000 ppb (gas) · 150 ng/l – 5 mg/l (liquid)
Response Time
~90 s (T90), delay ~300 s
Max. Chambers
up to 16 (ALV08/16 valve cluster)
Sample Phase
gas and liquid
Norm Reference
EN ISO 717-1 · ASTM D6007 · ASTM E1333

Norms & Standards

EN ISO 717-1ASTM D6007ASTM E1333GB/T 18801:2015

Cross-Sensitivities

The Hantzsch reaction with fluorimetric detection is only minimally sensitive to other aldehydes and ketones because of the short reaction time.

Benzaldehyde < 1:20000 · Acetaldehyde < 1:10000 · Acrolein < 1:10000 · NH₃ < 1:10000 · Propanal < 1:20000 · Glyoxal < 1:123 · Methanol < 1:50000 · H₂O₂ < 1:100 · O₃ < 1:500

No detectable interference: acetone, SO₂, NO₂, NO, isobutane

Fence-Line Formaldehyde Monitoring at an MDF Plant: The AL4021 in Regulatory Service in New Zealand

Situation

Under its air discharge permit, the MDF manufacturer Daiken Southland (New Zealand) has to demonstrate at six locations around the plant that 60 µg/m³ (30-minute average) is exceeded for no more than 0.5 % of the time in a year, and that 100 µg/m³ is never exceeded.

Solution

An AL4021 in a mobile measurement container with a computer and a cooling box for the reagents, relocated between the six measurement sites.

Result

At least one month per site, at least 40 weeks per year, 24/7 — with one instrument. At Daiken, the AL4021 is an IANZ-accredited analytical method (ISO/IEC 17025).

Read the full case study →

Frequently Asked Questions

How many test chambers can one AL4021 handle?
Up to 16, through an ALV08/16 valve cluster. The instrument steps through a programmable valve sequence and stores a unique chamber ID with every data point, so measurements to EN ISO 717-1, ASTM E1333 or ASTM D6007 run unattended without one analyser per chamber.
Is the AL4021 equivalent to the standard flask method?
Yes, and it has been shown externally. The Institut für Holztechnologie Dresden measured 20 chipboard samples with both the AL4021 and the flask/acetyl-acetone method to EN ISO 717-1; the regression confirms equivalency within the statistical error.
Can we also determine the total formaldehyde content of a sample, not just emission?
Yes. The sample is heated — in a micro-chamber such as the µ-CTE or by thermal desorption — and the released formaldehyde appears as a peak with an exponential decay. Integrating that peak gives the total content; the Aero-Laser Peak Integrator does this including baseline correction.

Request an Application Consultation

Tell us your measurement scenario — we'll recommend the right setup and send you relevant technical documentation.